Escient Network Router ZP 1 User Manual

Escient  
6640 Intech Blvd., Indianapolis, Indiana 46278  
Phone: 800-372-4368 Press "3” For Support  
Hours: Monday - Friday 9:00am - 7pm EST  
Fax: 317-616-6790  
ZP-1  
Net wor k Music Pl ayer  
Quick Setup  
Document Number: M51002-02A1  
November 2006  
AUDIO VIDEO INPUTS on A/V RECEIVER OR TV  
GETTING STARTED  
2
Connect the FireBall ZP-1 to your TV or A/V Receiver  
A) Locate the included three wire composite video (yellow) and analog  
audio (white and red) cable.  
SYSTEM REQUIREMENTS:  
A) Home ethernet network  
B) Broadband Internet access for product updates and  
product registration.  
C) One of the following FireBall Servers installed on the  
same ethernet network:  
POWER ADAPTER  
B) Connect the LEFT and RIGHT audio connectors (white and red) to the  
ANALOG AUDIO OUT jacks on the back of the ZP-1. Connect the  
video connector (yellow) to the Composite VIDEO OUT jack on the  
back of the ZP-1.  
HOME NETWORK (LAN)  
- FireBall FP-1 (with iPod docked)  
- FireBall AVX or MX  
- FirBall E or E2  
- FireBall DVDM-300 or DVDM-552  
- FireBall SE-80  
C) Connect the other end of the cable to an available set of ANALOG  
AUDIO IN and COMPOSITE VIDEO IN jacks on the back of your TV  
or A/V Receiver.  
D) TV or A/V receiver with video display  
Note: You may use optional s-video or component video cables and optical  
digital audio cables for the best picture and sound quality. Contact your  
Escient dealer for more information.  
3
Connect the FireBall ZP-1 to Your Home Network  
Note: The ZP-1 requires a home network and Internet connection to  
browse and play music from a FireBall server, to play Internet radio  
stations, and for general system maintenace.  
4
5
Power Up the ZP-1  
A) Connect the included Power Adapter to the ZP-1.  
B) Connect the Power Adapter to an AC outlet.  
1
Unpack Your New FireBall ZP-1  
FireBall ZP-1  
Handheld Remote  
Action: The Standby LED on the front of the FireBall will begin to  
flash RED during the power on cycle. When the LED turns solid RED,  
the FireBall is ready for use. Press the power button on the front panel  
or on the remote control. The LED will turn solid GREEN and video  
will be displayed on the TV when the unit is on.  
A) Connect the included ethernet cable from FireBall's  
ethernet jack to an open port on your Ethernet router.  
Two AAA batteries  
Ethernet Cable  
3 Wire Audio/Video Cable  
Power Adapter  
Escient Software and User’s Manual CD-Rom  
This Quick Setup Guide  
Note: If you want to connect your FireBall ZP-1 to a wireless network  
you will need to purchase an optional Ethernet to Wireless Bridge.  
Please contact your Escient dealer for more information.  
Note: You may have to press the "FB1" button on the remote to  
configure it to control FireBall. Also be sure the TV or A/V receiver are  
turned on and set to the correct input.  
A) Install the two AAA batteries into the remote  
QuickStart and Product Registration  
A) Use the remote control and follow the on-screen instructions.  
B) Make note of the serial number  
(located on the back)  
MORE SETUP  
SERIAL NUMBER:______________________________  
 

Craftsman Lawn Sweeper 486242223 User Manual
Crown Equipment Automobile SHR 5500 Series User Manual
Cub Cadet Lawn Mower SLT X1050 SLTX1054 User Manual
Cypress Computer Hardware CYS25G0101DX ATC User Manual
Delta Electronics Power Supply PFC3515V Series User Manual
Delta Electronics Power Supply SILM720 User Manual
Dukane Projector 2100 Series User Manual
EverFocus Security Camera ENVS1600 User Manual
Exido Toaster 243 031 User Manual
Fisher Price Motorized Toy Car T2057 User Manual